📢 Flat rate shipping below $10 in multiple countries! Limited offer ends May 31 🛒 Order now

Active

STLINK-V3MODS

STLINK v3 compact in-circuit debugger and programmer for STM32

ECCN US3A991.a.2
ECCN EUNEC
Packing TypeNot Applicable
RoHs compliantEcopack1
GradeIndustrial
Package NameCARD

STLINK-V3MODS is a small‑size debugging and programming probe for STM32 microcontrollers.The JTAG/SWD interfaces are used to communicate with any STM32 microcontroller located on an application board.STLINK-V3MODS also provides a Virtual COM port interface enabling the host PC to communicate with...
Read More

Key features
  • Modular probe with small size: approximately 15 × 30 mm
  • Direct‑to‑PCB implementation by 2 × 16‑pin 1.27 mm edge castellated vias, with all signals available in the required minimum PCB surface
  • Self-powered through a USB Micro-B connector
  • USB 2.0 high‑speed compatible interface
  • 5 V source output capability up to 200 mA
  • JTAG/SWD (Serial Wire Debug) specific features:
    • 3.0 to 3.6 V application voltage support and 5 V tolerant inputs
    • JTAG communication support
    • SWD and SWV (Serial Wire Viewer)
  • Virtual COM port (VCP) specific features:
    • 3.0 to 3.6 V application voltage support on the UART interface and 5 V tolerant inputs
    • VCP frequency up to 15 MHz
  • Multipath bridge USB to SPI/UART/I2C/CAN/GPIOs specific features:
    • 3.0 to 3.6 V application voltage support and 5 V tolerant inputs
  • Drag-and-drop flash programming
  • Two color LEDs: communication and power
In stock
Quantity $ per unit Savings
1-2$8.600%
Contact sales
$8.60
$8.59
ECCN US3A991.a.2
ECCN EUNEC
Packing TypeNot Applicable
RoHs compliantEcopack1
GradeIndustrial
Package NameCARD

STLINK-V3MODS is a small‑size debugging and programming probe for STM32 microcontrollers.The JTAG/SWD interfaces are used to communicate with any STM32 microcontroller located on an application board.STLINK-V3MODS also provides a Virtual COM port interface enabling the host PC to communicate with...
Read More

Key features
  • Modular probe with small size: approximately 15 × 30 mm
  • Direct‑to‑PCB implementation by 2 × 16‑pin 1.27 mm edge castellated vias, with all signals available in the required minimum PCB surface
  • Self-powered through a USB Micro-B connector
  • USB 2.0 high‑speed compatible interface
  • 5 V source output capability up to 200 mA
  • JTAG/SWD (Serial Wire Debug) specific features:
    • 3.0 to 3.6 V application voltage support and 5 V tolerant inputs
    • JTAG communication support
    • SWD and SWV (Serial Wire Viewer)
  • Virtual COM port (VCP) specific features:
    • 3.0 to 3.6 V application voltage support on the UART interface and 5 V tolerant inputs
    • VCP frequency up to 15 MHz
  • Multipath bridge USB to SPI/UART/I2C/CAN/GPIOs specific features:
    • 3.0 to 3.6 V application voltage support and 5 V tolerant inputs
  • Drag-and-drop flash programming
  • Two color LEDs: communication and power