📢 Flat rate shipping below $10 in multiple countries! Limited offer ends May 31 🛒 Order now

Active

EVSPIN32G4

STSPIN32G4 demonstration board for three-phase brushless motors

Target Application3-phase Field Oriented Control (FOC)
Core ProductSTSPIN32G4, STL110N10F7
ECCN USEAR99
ECCN EUNEC
Packing TypeNot Applicable
RoHs compliantEcopack1
GradeIndustrial
Package NameCARD

The EVSPIN32G4 is a demonstration board based on the STSPIN32G4 system in package and STL110N10F7 power MOSFETs. The STSPIN32G4 integrates in a 9x9 mm VFQFPN package, a triple high-performance half-bridge gate driver with a rich set of programmable features and one mixed signal STM32G431...
Read More

Key features
  • Input bus voltage from 10 V to 75 V with dedicated monitoring
  • Power stage based on the STL110N10F7 power MOSFETs with output current up to 20 Arms (with heatsink mounted) and protected to overcurrent conditions
  • STSPIN32G4, high performance three-phase motor controller with embedded STM32G431 MCU:
    • 32-bit ARM® Cortex®-M4 MCU+FPU
    • Up to 170 MHz clock frequency
    • CORDIC mathematical hardware accelerator for trigonometric functions
    • 128 kB Flash memory with proprietary code readout protection (PCROP), securable memory area, 1 kB OTP
    • 32 kB SRAM memory with HW parity check
    • 2 x advanced timers for motor control, 16-bit with up to 6 x PWM channels each
    • 8 x general purpose timers
    • 2 x ADCs 12-bit resolution (up to 19 channels) with 4 Msps conversion rate
    • 4 x 12-bit DAC channels
    • 4 x ultra-fast rail-to-rail comparators
    • 3 x rail-to-rail operational amplifiers usable also in PGA mode
    • Internal high precision voltage reference
    • Up to 40 GPIOs
    • Full set of interfaces: I2C, SPI, UART and CAN
    • VCC buck converter up to 200 mA, with programmable output and embedded MOSFET
    • 3.3 V LDO linear regulator up to 150 mA
    • Low quiescent linear regulator for MCU supply in standby mode
    • Regulators with full set of protection features; thermal shutdown, short-circuit and overload protections
    • 75 V rated gate drivers with 1 A sink/source current and embedded bootstrap diodes
    • Drain-source voltage sensing of each power MOSFET
  • Three-shunt or single-shunt configurable current sensing
  • Digital Hall sensor and quadrature encored input
  • ST-LINK/V2 programmer and debugger
  • Arduino UNO connector
  • Predisposition for CAN bus
  • NTC sensor for power stage temperature monitoring
Out of Stock
Quantity $ per unit Savings
1$307.360%
Contact sales
$307.36
Target Application3-phase Field Oriented Control (FOC)
Core ProductSTSPIN32G4, STL110N10F7
ECCN USEAR99
ECCN EUNEC
Packing TypeNot Applicable
RoHs compliantEcopack1
GradeIndustrial
Package NameCARD

The EVSPIN32G4 is a demonstration board based on the STSPIN32G4 system in package and STL110N10F7 power MOSFETs. The STSPIN32G4 integrates in a 9x9 mm VFQFPN package, a triple high-performance half-bridge gate driver with a rich set of programmable features and one mixed signal STM32G431...
Read More

Key features
  • Input bus voltage from 10 V to 75 V with dedicated monitoring
  • Power stage based on the STL110N10F7 power MOSFETs with output current up to 20 Arms (with heatsink mounted) and protected to overcurrent conditions
  • STSPIN32G4, high performance three-phase motor controller with embedded STM32G431 MCU:
    • 32-bit ARM® Cortex®-M4 MCU+FPU
    • Up to 170 MHz clock frequency
    • CORDIC mathematical hardware accelerator for trigonometric functions
    • 128 kB Flash memory with proprietary code readout protection (PCROP), securable memory area, 1 kB OTP
    • 32 kB SRAM memory with HW parity check
    • 2 x advanced timers for motor control, 16-bit with up to 6 x PWM channels each
    • 8 x general purpose timers
    • 2 x ADCs 12-bit resolution (up to 19 channels) with 4 Msps conversion rate
    • 4 x 12-bit DAC channels
    • 4 x ultra-fast rail-to-rail comparators
    • 3 x rail-to-rail operational amplifiers usable also in PGA mode
    • Internal high precision voltage reference
    • Up to 40 GPIOs
    • Full set of interfaces: I2C, SPI, UART and CAN
    • VCC buck converter up to 200 mA, with programmable output and embedded MOSFET
    • 3.3 V LDO linear regulator up to 150 mA
    • Low quiescent linear regulator for MCU supply in standby mode
    • Regulators with full set of protection features; thermal shutdown, short-circuit and overload protections
    • 75 V rated gate drivers with 1 A sink/source current and embedded bootstrap diodes
    • Drain-source voltage sensing of each power MOSFET
  • Three-shunt or single-shunt configurable current sensing
  • Digital Hall sensor and quadrature encored input
  • ST-LINK/V2 programmer and debugger
  • Arduino UNO connector
  • Predisposition for CAN bus
  • NTC sensor for power stage temperature monitoring