Currency
USD
  • Language
    English
    • Toggle Nav
    Cart 0
    Search
    Advanced Search
    Menu
    Account
    Settings
  • Language
    English
    • Currency
    USD

    Flat $5.99 shipping rate worldwide throughout May - no code needed! Start your design today. Flat $5.99 shipping rate worldwide throughout May - no code needed! Start your design today. Flat $5.99 shipping rate worldwide throughout May - no code needed! Start your design today. Flat $5.99 shipping rate worldwide throughout May - no code needed! Start your design today. Flat $5.99 shipping rate worldwide throughout May - no code needed! Start your design today.

    main product photo

    P-NUCLEO-IOM01M1

    Active

    STM32 Nucleo pack for IO-Link master with IO-Link v1.1 PHY and stack
    Learn More about P-NUCLEO-IOM01M1

    Quantity $ per Unit Savings
    1 - 2$62.480%
    2 + Contact Sales
    Save to My List Compare
    In stock
    $62.48
    Parameter NameParameter Value
    Core ProductL6360
    ECCN USEAR99
    ECCN EUNEC
    Packing TypeNot Applicable
    ROHS Compliance GradeEcopack2
    GradeIndustrial
    Package NameCARD

    The P-NUCLEO-IOM01M1 is an STM32 Nucleo pack composed of the STEVAL-IOM001V1 and the NUCLEO-F446RE boards. The STEVAL-IOM001V1 is a single IO-Link master PHY layer (L6360) while the NUCLEO- F446RE runs an IO-Link stack rev 1.1 (developed by and property of TEConcept GmbH, license limited to 10k minutes, renewable without additional costs). IO-Link stack update is allowed exclusively by following the procedure described in UM2421 (freely available at www.st.com). Any other erase/overwrite of the pre-loaded stack makes impossible to restore it.


    The STM32 Nucleo pack provides an affordable and easy-to-use solution for the evaluation of IO-Link applications, L6360 communication features and robustness, together with the STM32F446RET6 computation performance. The pack, hosting up to four STEVAL-IOM001V1 to build a quad port IO-Link master, can access the IO-Link physical layer and communicate with IO-Link Devices.


    You can evaluate the tool via the dedicated GUI (IO-Link Control Tool©, property of TEConcept GmbH) or use it as an IO-Link master bridge accessible from the dedicated SPI interface: source code of demo project (Low-Level IO-Link Master Access Demo Application, developed by TEConcept GmbH) and API specification are available for free.

    Key features
    • IO-Link master stack v.1.1 (property of TEConcept GmbH):
      • renewable 10k minutes license
      • ready for new version update
    • STEVAL-IOM001V1
      • IO-Link master PHY based on L6360
      • Interrupt diagnostics pin
      • I²C and UART interface
      • SPI (slave) interface
      • 65 mA selectable (3.3 or 5.0 V) linear regulator
      • CQ (push-pull) and L+ (high side) switches
      • IQ additional IEC61131-2 type 1 digital input
      • L+ and CQ overload and overheating protections with non-dissipative cut-off function
      • QFN-26L (3.5x5x1 mm) package
      • Operating voltage range from 18 to 32.5 V
      • Additional high side switch for L+ heavy loads (IPS161H)
      • LEDs for status and diagnostics
      • Ground and VCC wire break protections
      • EMC compliance with IEC61000-4-2, IEC61000-4-3, IEC61000-4-5
      • Equipped with ST morpho connectors
      • CE certified
      • RoHS and China RoHS compliant
    • NUCLEO-F446RE
      • STM32F446RET6 32-bit Micro-controller based on ARM®Cortex®-M4 core (180 MHz max.) with 512-Kbyte Flash memory and 128 (+4) Kbyte RAM
      • Two types of extension resources: Arduino™ UNO Revision 3 connectivity and ST morpho extension pin headers for full access to all STM32 I/Os
      • Mbed-enabled (http://mbed.org)
      • On-board ST-LINK/V2-1 debugger/programmer with SWD connector: selection-mode switch to use the kit as a standalone ST-LINK/V2-1
      • Two push-buttons: USER and RESET
    Associated Products