L9963E

Automotive chip for battery management applications with daisy chain up to 31 devices

Parameters

Operating Temp Min Celsius	105.0
Operating Temp Max Celsius	-40.0
ECCN US	EAR99
ECCN EU	NEC
Packing Type	Tray
RoHs compliant	Ecopack2
Grade	Automotive Safety
Package Name	TQFP-EP 64 10X10X1.0 MM

Description

The L9963E is a Li-ion battery monitoring and protecting chip for high-reliability automotive applications and energy storage systems. Up to 14 stacked battery cells can be monitored to meet the requirements of 48 V and higher voltage systems.Each cell voltage is measured with high accuracy, as...
Read More

Key features

Key features
AEC-Q100 qualified Measures 4 to 14 cells in series, with 0 μs desynchronization delay between samples. Supports also busbar connection without altering cell results Coulomb counter supporting pack overcurrent detection in both ignition on and off states. Fully synchronized current and voltage samples 16-bit voltage ADC with maximum error of ±2 mV in the [0.5 – 4.3] V range, after soldering, in [-40; +105] °C Tj range 2.66 Mbps isolated serial communication with regenerative buffer, supporting dual access ring. Less than 4 us latency between start of conversion of the 1st and the 31st device in a chain. Less than 4 ms to convert and read 96 cells in a system using 8 L9963E and L9963T transceiver. Less than 8 ms to convert and read 210 cells in a system using 15 L9963E and L9963T transceiver. Less than 16 ms to convert and read 434 cells in a system using 31 L9963E and L9963T transceiver. Supports both XFMR and CAP based isolation 200 mA passive internal balancing current for each cell in both normal and silent-balancing mode. Possibility of executing cyclic wake up measurements. Manual/Timed balancing, on multiple channels simultaneously; Internal/External balancing Fully redundant cell measurement path, with ADC Swap, for enhanced safety and limp home functionality Intelligent diagnostic routine providing automatic failure validation. Redundant fault notification through both SPI Global Status Word (GSW) and dedicated FAULT line Two 5 V regulators supporting external load connection with 25 mA (VCOM) and 50 mA (VTREF) current capability 9 GPIOs, with up to 7 analog inputs for NTC sensing Robust hot-plug performance. No Zeners needed in parallel to each cell Full ISO26262 compliant, ASIL-D systems ready

Out of Stock

Parameters

Operating Temp Min Celsius	105.0
Operating Temp Max Celsius	-40.0
ECCN US	EAR99
ECCN EU	NEC
Packing Type	Tray
RoHs compliant	Ecopack2
Grade	Automotive Safety
Package Name	TQFP-EP 64 10X10X1.0 MM

Description

Key features

Key features
AEC-Q100 qualified Measures 4 to 14 cells in series, with 0 μs desynchronization delay between samples. Supports also busbar connection without altering cell results Coulomb counter supporting pack overcurrent detection in both ignition on and off states. Fully synchronized current and voltage samples 16-bit voltage ADC with maximum error of ±2 mV in the [0.5 – 4.3] V range, after soldering, in [-40; +105] °C Tj range 2.66 Mbps isolated serial communication with regenerative buffer, supporting dual access ring. Less than 4 us latency between start of conversion of the 1st and the 31st device in a chain. Less than 4 ms to convert and read 96 cells in a system using 8 L9963E and L9963T transceiver. Less than 8 ms to convert and read 210 cells in a system using 15 L9963E and L9963T transceiver. Less than 16 ms to convert and read 434 cells in a system using 31 L9963E and L9963T transceiver. Supports both XFMR and CAP based isolation 200 mA passive internal balancing current for each cell in both normal and silent-balancing mode. Possibility of executing cyclic wake up measurements. Manual/Timed balancing, on multiple channels simultaneously; Internal/External balancing Fully redundant cell measurement path, with ADC Swap, for enhanced safety and limp home functionality Intelligent diagnostic routine providing automatic failure validation. Redundant fault notification through both SPI Global Status Word (GSW) and dedicated FAULT line Two 5 V regulators supporting external load connection with 25 mA (VCOM) and 50 mA (VTREF) current capability 9 GPIOs, with up to 7 analog inputs for NTC sensing Robust hot-plug performance. No Zeners needed in parallel to each cell Full ISO26262 compliant, ASIL-D systems ready